(a 4-port “long cable” “external box” USB hub)
.
-as of [18 JUNE 2024]–
.
.
-a [USB hub] is a ‘device’ that expands a single ‘Universal Serial Bus'(USB) port into several so that there are more ‘ports’ available to connect devices to a host system, similar to a [power strip]-
.
All devices connected through a USB hub share the bandwidth available to that hub
USB hubs are often built into equipment such as computer cases, keyboards, monitors, or printers.
When such a device has many USB ports, they all usually stem from one or two internal USB ports rather than each port having independent USB circuitry.
Physically separate USB hubs come in a wide variety of form factors:
from external boxes (looking similar to an Ethernet or network hub) connectable with a cable,
to small designs that can be directly plugged into a USB port
(see the “compact design” picture).
In the middle case, there are “short cable” hubs which typically use an integral 6-inch cable to slightly distance a small hub away from physical port congestion and of course increase the number of available ports.
Laptop/notebook computers may be equipped with USB ports, but an external USB hub can consolidate several everyday devices (like a mouse and a printer) into a single hub to enable one-step attachment and removal of all the devices.
Some USB hubs may support power delivery (PD) and charging if they’re self-powered and certified, though they may start to be referred to as a simple docking station at this point
.
Physical layout
A “star” “short cable” external USB hub with the plastic casing removed
A USB network is built from USB hubs connected downstream to USB ports, which themselves may stem from USB hubs.
USB hubs can extend a USB network to a maximum of 127 ports.
The USB specification requires that bus-powered/passive hubs may not be connected in series to other bus-powered hubs.
Depending on vendor and design, USB ports are often closely spaced.
Consequently, plugging a device into one port may physically block an adjacent port, particularly when the plug is not part of a cable but is integral to a device such as a USB flash drive.
A horizontal array of horizontal sockets may be easy to fabricate, but may cause only two out of four ports to be usable (depending on plug width).
Port arrays in which the port orientation is perpendicular to the array orientation generally have fewer blockage problems.
External “Octopus” or “Squid” hubs (with each socket at the end of a very short cable maybe 2 inches long), or “star” hubs (with each port facing in a different direction, as pictured) avoid this problem completely
.mo
Length limitations
USB cables are limited to 3 metres (10 feet) for low-speed USB 1.1 devices.
A hub can be used as an active USB repeater to extend cable length for up to 5 metre (16 feet) lengths at a time.
Active cables (specialized connector-embedded one-port hubs) perform the same function, but since they are strictly bus-powered, externally powered (non-bus-powered) USB hubs would likely be required for some of the segments.
Power
A bus-powered hub (passive hub) is a hub that draws all its power from the host computer’s USB interface.
It does not need a separate power connection.
However, many devices require more power than this method can provide and will not work in this type of hub.
It may be desirable to use a bus-powered hub with self-powered external hard-disk units, as they may not go into sleep mode immediately upon computer shut-down or sleep mode when using a self-powered hub since they will continue to see a power source on the USB ports when using a self-powered hub.
A USB’s electric current is allocated in units of 100 mA up to a maximum total of 500 mA per port.
Therefore, a compliant bus powered hub can have no more than four downstream ports and cannot offer more than four 100 mA units of current in total to downstream devices (since the hub needs one unit for itself).
If a device requires more units of current than the port it is plugged into can supply, the operating system usually reports this to the user.
In contrast, a self-powered hub (active hub) is one that takes its power from an external power supply unit and can therefore provide full power (up to 500 mA) to every port.
Many hubs can operate as either bus powered or self powered hubs.
However, there are many non-compliant hubs on the market which announce themselves to the host as self-powered despite really being bus-powered.
Equally there are plenty of non-compliant devices that use more than 100 mA without announcing this fact (or indeed sometimes without identifying themselves as USB devices at all).
These hubs and devices do allow more flexibility in the use of power (in particular many devices use far less than 100 mA and many USB ports can supply more than 500 mA before going into overload shut-off), but they are likely to make power problems harder to diagnose.
Some self-powered hubs do not supply enough power to drive a 500 mA load on every port.
For example, many seven port hubs have a 1 A power supply, when in fact seven ports could draw a maximum of 7 x 0.5 = 3.5 A, plus power for the hub itself.
Designers assume the user will most likely connect many low power devices and only one or two requiring a full 500 mA.
On the other hand, the packaging for some self-powered hubs states explicitly how many of the ports can drive a 500 mA full load at once.
For example, the packaging on a seven-port hub might claim to support a maximum of four full-load devices.
Dynamic-powered hubs are hubs which can work as bus-powered as well as self-powered hubs.
They can automatically switch between modes depending on whether a separate power supply is available or not. While switching from bus-powered to self-powered operation does not necessarily require immediate renegotiations with the host,
switching from self-powered to bus-powered operation may cause USB connections to be reset if connected devices previously requested more power than still available in bus-powered mode
.
Speed
Hub Demo Board from VIA shows all internal components of a hub
To allow high-speed (USB 2.0) devices to operate in their fastest mode, all hubs between the devices and the computer must be high-speed.
High-speed devices should fall back to full-speed (USB 1.1) when plugged into a full-speed hub (or connected to an older full-speed computer port).
While high-speed hubs can communicate at all device speeds, low- and full-speed traffic is combined and segregated from high-speed traffic through a transaction translator.
Each transaction translator segregates lower speed traffic into its own pool, essentially creating a virtual full-speed bus.
Some designs use a single transaction translator (STT), while other designs have multiple translators (MTT)
Having multiple translators is a significant benefit when one connects multiple high-bandwidth full-speed devices
It is an important consideration that in common language (and often product marketing), USB 2.0 is used as synonymous with high-speed.
However, because the USB 2.0 specification, which introduced high-speed, incorporates the USB 1.1 specification such that a USB 2.0 device is not required to operate at high speed, any compliant full-speed or low-speed device may still be labelled as a USB 2.0 device.
Thus, not all USB 2.0 hubs operate at high speed.
USB 3.0 is the third major version of the Universal Serial Bus (USB) standard for interfacing computers and electronic devices
Among other improvements, USB 3.0 adds the new transfer rate referred to as SuperSpeed USB (SS) that can transfer data at up to 5 Gbit/s (625 MB/s), which is about 10 times faster than the USB 2.0 standard
It is recommended that manufacturers distinguish USB 3.0 connectors from their USB 2.0 counterparts by using blue (Pantone 300C)[3] for the Standard-A receptacles and plugs,[4] and by the initials SS.[5]
USB 3.1, released in July 2013, is the successor standard that replaces the USB 3.0 standard. USB 3.1 preserves the existing SuperSpeed transfer rate, giving it the new label USB 3.1 Gen 1,[6][7] while defining a new SuperSpeed+ transfer mode, called USB 3.1 Gen 2[8] which can transfer data at up to 10 Gbit/s over the existing USB-type-A and USB-C connectors (1250 MB/s, twice the rate of USB 3.0).[9][10]
USB 3.2, released in September 2017, replaces the USB 3.1 standard. It preserves existing USB 3.1 SuperSpeed and SuperSpeed+ data modes and introduces two new SuperSpeed+transfer modes over the USB-C connector using two-lane operation, with data rates of 10 and 20 Gbit/s (1250 and 2500 MB/s).
Protocol[edit]
Each hub has exactly one upstream port and a number of downstream ports. The upstream port connects the hub (directly or through other hubs) to the host. Other hubs or devices can be attached to the downstream ports. During normal transmission, hubs are essentially transparent: data received from its upstream port is broadcast to all devices attached to its downstream ports (pictorially described in the USB 2.0 specification in Figure 11-2. Hub Signaling Connectivity); data received from a downstream port is generally forwarded to the upstream port only. This way, what is sent by the host is received by all hubs and devices, and what is sent by a device is received by the host but not by the other devices (an exception is resume signalling). Downstream routing has been changed in USB 3.0 with the addition of Point to Point routing: A route string sent in the packet header allows a USB 3.0 host to only send a downstream packet to a single destination port, decreasing congestion and power consumption.[11]
Hubs are not transparent when dealing with changes in the status of downstream ports, such as insertion or removal of devices. In particular, if a downstream port of a hub changes status, this change is dealt with in an interaction between the host and this hub; the hubs between them act as transparent in this case.
To this aim, each hub has a single interrupt endpoint “1 IN” (endpoint address 1, hub-to-host direction) used to signal changes in the status of the downstream ports. When someone plugs in a device, the hub detects voltage on either D+ or D- and signals the insertion to the host via this interrupt endpoint. When the host polls this interrupt endpoint, it learns that the new device is present. It then instructs the hub (via the default control pipe) to reset the port where the new device was plugged in. This reset makes the new device assume address 0, and the host can then interact with it directly; this interaction will result in the host assigning a new (non-zero) address to the device.[12][13]
Transaction translator[edit]
Any USB 2.0 hub that supports a higher standard than USB 1.1 (12 Mbit/s) will translate between the lower standard and the higher standard using what is called a transaction translator (TT). For example, if a USB 1.1 device is connected to a port on a USB 2.0 hub, then the TT would automatically recognize and translate the USB 1.1 signals to USB 2.0 on the uplink. However, the default design is that all lower-standard devices share the same transaction translator and thus create a bottleneck, a configuration known as the single transaction translator. Consequently, multi transaction translators (Multi-TT) were created, which provide more transaction translators such that bottlenecks are avoided.[14] Note that USB 3.0 hubs do not currently[15][citation needed] perform transaction translation to super-speed for USB 2.0 devices.
Electronic design[edit]
Most USB hubs use one or more integrated controllers (ICs), of which several designs are available from various manufacturers. Most support a four-port hub system, but hubs using 16-port hub controllers are also available in the industry.[citation needed] The USB bus allows seven cascading tiers of ports. The root hub is the first tier, and the last devices are on the seventh tier, which allows 5 tiers worth of hubs between them. The maximum number of user devices is reduced by the number of hubs. With 50 hubs attached, the maximum number is 127 − 50 = 77.[16]
Inverse or sharing hubs (KVM)[edit]
Also available are so-called “sharing hubs”, which effectively are the reverse of a USB hub, allowing several PCs to access (usually) a single peripheral. They can either be manual, effectively a simple switch-box, or automatic, incorporating a mechanism that recognizes which PC wishes to use the peripheral and switches accordingly. They cannot grant both PCs access at once. Some models, however, have the ability to control multiple peripherals separately (e.g., two PCs and four peripherals, assigning access separately). Only the simpler switches tend to be automatic, and this feature generally places them at a higher price point too. Modern “keyboard, video and mouse” switches (KVM) can also often share USB devices between several computers.
See also[edit]
USB On-The-Go
References[edit]
^ What Is the Difference Between Powered & Non-Powered USB Hubs?
^ USB Technology: Multi-TT Hub Goes Head-to-Head With Single-TT. Tom’s Hardware UK and Ireland. Retrieved 2006-08-24.
^ “USB-IF Compliance Updates”. USB Implementers Forum. 1 June 2011. Retrieved 14 August 2020.
^ “Universal Serial Bus Revision 3.1 Specification”. usb.org. pp. 5–20. Archived from the original (ZIP) on 12 April 2016. Retrieved 12 April 2016.[verification needed]
^ McFedries, Paul (2013). “Connecting USB Devices”. PCs for Grown-Ups: Getting the Most Out of Your Windows 8 Computer. Indianapolis: Que Publishing. ISBN 978-0-13-303501-8. Retrieved 2016-02-18. Most PC manufacturers label each USB port using the logo for USB type […] the USB 2.0 logo is a trident, while the USB 3.0 logo is a similar trident with the letters ‘SS’ (which stands for SuperSpeed) attached.[verification needed]
^ “USB 3.1 Specification Language Usage Guidelines from USB-IF” (PDF). Archived from the original (PDF) on 12 March 2016. Retrieved 10 March 2016.[verification needed]
^ “USB 3.1 Gen 1 & Gen 2 explained”. msi.com.[verification needed]
^ “USB 3.1 Specification Language Usage Guidelines from USB-IF” (PDF). Archived from the original (PDF) on 12 March 2016. Retrieved 10 March 2016.[verification needed]
^ “USB 3.2 Specification”. usb.org. USB Implementers Forum, Inc. Retrieved 30 August 2018.[verification needed]
^ “Universal Serial Bus Revision 3.1 Specification”. usb.org. Archived from the original (ZIP) on 21 November 2014. Retrieved 19 November 2014.[verification needed]
^ What’s The Difference Between USB 2.0 And 3.0 Hubs?
^ USB 2.0 specification Archived 2012-02-07 at the Wayback Machine
^ USB in a nutshell
^ “Single TT Or Multi TT: USB Technology: Multi-TT Hub Goes Head-to-Head With Single-TT”. tomshardware.com. 2003-09-09. Retrieved 2013-05-01.
^ “What is USB? » Hardware » Windows » Tech Ease”. Retrieved 2019-07-04.
^ A.P.Godse; D.A.Godse (2009-01-01). Advance Microprocessors. Technical Publications. p. 16. ISBN 978-81-8431-560-8. Retrieved 2013-01-03.
External links[edit]
Wikimedia Commons has media related to USB hubs.
en.wikipedia.org /wiki/USB_hub
USB hub
Contributors to Wikimedia projects
14-18 minutes
Ambox current red Americas.svg
This article needs to be updated. Please update this article to reflect recent events or newly available information. (May 2017)
A four-port “long cable” “external box” USB hub
A four-port “compact design” USB hub: upstream and downstream ports shown
.
.
*USB HUB JOURNALS* –>
*order from amazon*
“SABRENT 4-PORT USB 2.0 HUB”
(with LED lit power switches)
(HB-UMLS)
$7.99
(with the rest of a $25 amazon gift card)
“connecting differently”
PC/MAC COMPATIBLE
USB 2.0
HIGH SPEED
.
*HIGH SPEED* –> 480 Mbps
*”FULL SPEED”* –> 12 Mbps
(???)
*LOW SPEED* –> 1.5 Mbps
.
“127 USB”
(which is the maximum # of devices you can connect to a single USB port)
*HB-UMLS*
(the ‘sabrent’ model #)
.
(arrives ’16 january 2021′)
.
.
*THE BEST USB HUBS*
(via ‘PC mag’)
ALLFU 8-in-1 USB C Hub
.
(out of stock @ ‘amazon’???)
.
*25 AUGUST 2022*
*the ‘lention hub’ is unreliable*
.
*so i ordered a 2nd (lower-end) model* –>
.
.
*👨🔬🕵️♀️🙇♀️*SKETCHES*🙇♂️👩🔬🕵️♂️*
.
.
.
.
.
💕💝💖💓🖤💙🖤💙🖤💙🖤❤️💚💛🧡❣️💞💔💘❣️🧡💛💚❤️🖤💜🖤💙🖤💙🖤💗💖💝💘
.
.
*🌈✨ *TABLE OF CONTENTS* ✨🌷*
.
.
🔥🔥🔥🔥🔥🔥🔥*we won the war* 🔥🔥🔥🔥🔥🔥🔥