-ROOM SPEX- - -KINGDOM OF JOGA-

-as of [31 AUGUST 2024]–

-BODY RULERS-

*OUR METER STIX*

*STAPLES* ==>

*MEDICINE JARS*

solo akustika

*STACKS*

(tri-pod arrangements)

*COMMON ROOM DOOR*

*[90 CM] WIDE*

(45cm midpoint)

*BASE-BOARD HEIGHT*

*14 centi-meters*

*BASE-BOARD WIDTH*

*2 centi-meters*

*height*

*baseboard top* –> “center window sill”

*52 centi-meters*

*center window-sill is 66 centi-meters from floor*

*’diagonal’ from ‘baseboard inner top’ to ‘center window sill edge’* –>

*52.04 centi-meters*

*CENTER BASEBOARD –>

*horizontal rectangle*

111 cm x 14 cm

*1554 square centi-meters*

*CENTER BASEBOARD TOP* –>

-111 cm- x -2 cm-

*222 square centi-meters*

*CENTER WALL*

(between ‘baseboard’ + ‘center window sill’)

111 cm width x 52 cm height

*5772 square centi-meters*

*CENTER WINDOW SILL* –>

*horizontal rectangle*

*~87.5 centi-meters wide*

(less than ‘1 meter’)

*38.5 centi-meters ‘tall’*

*ARQ* –>

2.27

(too wide for 16:9)

(cut some of the width)

midpoint ->

43.75 width / 19.25 height

*forms a ‘trapezoid’ with ‘floor length’*

*top side starts ’11 cm’ to the left of the base*

*top side ends ’15 cm’ to the right of the base*

*windows are ‘181 cm’ bottom to top*

*meaning that the ‘window top’ was 247 cm from ‘ground level’*

87.5 cm / 111 cm

9:16 —>

197cm height

16:9 —>

[111cm width]

*CEILINGS* –>

14 cm baseboard

(261 cm from ‘baseboard top’ to ‘ceiling’)

*275 cm ceilings*

~9.02 feet

*main door* –>

254 cm

(‘floor’ to ‘top of door’)

*’8 FEET’ / ‘4 INCHES’*

*2 DOOR SIDE-BOARDS* –>

*parallel to door* –>

-8.5 CM-

*2 progressively thinner ‘boards’ are stacked on the ‘perpendicular entrance sidebar’*

*each of them are ~1 cm ‘tall’*

(so they add less than 2 cm to your ‘8.5 cm length’)

*the 3 ‘door boards’ share a ‘center’*

*this center is actually ‘5.5 cm’*

(in –> out)

(this is the ‘midpoint’ of the ‘top board’)

*the total ‘length’ is ~ 13 cm*

(so ‘true center’ would be ~6.5 cm)

*divided into 5 sections*

(for 13 cm total) –>

*section 1* –>

the difference in length of 1/2 ‘board A’ (longest) + 1/2 ‘board B’ (2nd longest)

*section 2*–>

*the difference in length of 1/2 ‘board B’ (2nd longest) + 1/2 ‘board C’ (3rd longest)*

*section 3* –>

*the length of ‘board C’ (3rd longest / top)*

*section 4*

(repeat ‘section 1’ for the other side)

*section 5*

(repeat ‘section 2’ for the other side)

*’board b’ facilitates a ‘door hinge’*

*1 hinge side is attached to the ‘board B’ height and ‘board A ‘top’*

(1cm x 2cm)

*4 DOOR HINGES*

*each hinge is 10 cm* in ‘height’*

(roughly divided into 5 ‘2 cm segments’)

(from ‘bottom’ to ‘top’…)

*hinge 1* –>

bottom – 20 cm

top – 30 cm

*hinge 2* –>

bottom – 87 cm

top – 97 cm

*hinge 3* –>

bottom – 153 cm

top – 163 cm

*hinge 4* –>

bottom – 218 cm

top – 228 cm

*top of ‘hinge 4’ –> bottom of ‘top door board’

*18 CM*

*each ‘hinge’ requires 8 screws*

*4 vertical screws to attach ‘hinge side 1’ to the ‘door thickness’*

*4 vertical screws to attach ‘hinge side 2’ to on the ‘top’ of ‘sideboard C’*

*246 CM FROM FLOOR TO ‘BOTTOM’ OF ‘TOP DOOR BOARD’*

*bottom of ‘top door board’ –> ‘top of ‘top door board’

~9 CM

*255 CM FROM FLOOR TO ‘TOP’ OF ‘TOP DOOR BOARD’*

*the 246cm + 255cm measurements are ‘8.5 cm apart’*

(so diagonal connecting their peaks is 12.38 cm)

*’20 CM’ FROM ‘TOP’ OF ‘TOP DOOR BOARD’ TO ‘CEILING’*

*the door opens into the room from the left side*

*the door is 75.cm wide / 243.cm tall*

*2.5 cm bottom gap*

*there should be no gap on ‘hinge side’ of door*

*minimize gaps on the ‘swing side’/’top’ of door*

how?

*the door is ‘4 cm thick’*

*the door swings into the room from left side*

*turn door 90 degrees CC so that it is parallel with the ‘left sideboard’*

*there will be a ~2CM gap between left side of door and the left door side baseboard*

*your ‘left wall’ and ‘door’ should be parallel*

(roughly 8.5cm apart)

*the ‘door’ starts 2cm behind the beginning of ‘left wall’*

(the left wall baseboard thickness needs to be taken into account when measuring distance from the ‘parallel lines’)

*from outside, push into the door until ‘protruding 5.5cm doorknob’ touches the left wall*

*mark it up with ‘masking tape’*

*the ‘left wall mark’ should be ~75cm from the ‘nearest corner’*

*beginning of the room is

start measuring the room from the ‘inner side’ of the ‘sideboard that the latch plate is attached to

*an ‘inverted door’ is cut into each side of the door*

~1.25 cm invert length

*so that the ‘inverted door’ is ~ 1.5 cm thick*

*the ‘door entrance is ~76.5cm*

*for the rest of the perimeter, there are baseboards that protrude ~2cm into the room*

*in ‘bottom left corner’, the ‘left wall sideboard’ intersects into the ‘south wall sideboard’ in a way that protrudes ‘2cm’ from the left wall*

*WHEN VIEWING THE DOOR FROM INSIDE THE ROOM* –>

27.5 cm from ‘bottom of door’ to ‘bottom of inverted door”

*16 cm from ‘top of inverted door’ to ‘top of door’*

*the ‘inverted door’ is 2 meters tall*

*12 cm from ‘left side of door’ to ‘left side of inverted door”*

*12 cm from ‘right side of inverted door’ to ‘right side of door’*

*the ‘inverted door’ is ’51 CM’ wide*

*’doorknob’ to the left of ‘inverted door’*

3.25 cm radius

6.5 cm diameter

(use ‘diameter tape’ to measure ‘circumference’)

the ‘inside doorknob protrusion’ consists of 3 cylinders

*outer cylinder has ~3.5 cm radius*

*2nd outer cylinder has ~1.5 cm radius*

*3rd outer cylinder has ~1 cm radius*

*from inside, the ‘door knob’ protrudes *~5.5CM* into the room*

*from inside, the ‘spindle’ protrudes *~11.5 CM* right*

*2 screws*
(left / right side)

(from ‘inside room’ to ‘outside room’)

(inner cylinder)

*the knob is in a ‘horizontal position’ when door is unlocked*

*to lock door from the inside, turn the knob 90 degrees left*
(so that the knob is now in a ‘vertical alignment’)

*when ‘locked’, the spindle cannot be rotated*

*to unlock door from inside, turn the knob 90 degrees right*
(so that the knob is now in a ‘horizontal alignment’)

*the ‘spindle’ is positioned to the right of the knob*

*to open door from inside, push down on the ‘spindle’ to rotate clockwise*

*the spindle can only rotate less than 90 degrees clockwise*

*and pull door towards you*

*the ‘latch plate’ is screwed into the left ‘perpendicular door sidebar’*

~12 cm long

*bottom of ‘latch plate’ is positioned ~88cm high*

(so top of ‘latch plate’ is positioned ~1 meter high)

*use 4 screws to fasten ‘latch plate’ to your perpendicular sidebar*

*2 larger screws at ‘top center’ / ‘bottom center’*

*1 small black screw in ‘top left corner’*

*1 small black screw in ‘bottom right corner’*

*192.5 CM*

(bottom left corner –> bottom right corner

100 / 8.5 / 84

*63 CM*

*TURN RIGHT*

*the ‘floor baseboard is [7.5 cm]*

*the ‘closet sideboard is [9 cm]*

*from ceiling to ‘top of closet topboard* –>

[19 cm]

*from ceiling to top of floor baseboard –.

[262 cm]

*from floor to ceiling* –>

[276 cm]

*CLOSET*

*’closet door’ similar set up to ‘main door’*

(except the knob is on the right side of the door)

(and the spindle points left)

(and there is no ‘locking knob’ on either side)

*the knob protrudes [5.5 cm]

*the ‘closet door’ is [60.5 cm] wide*

closet floor rectangle

[80 cm] x [50 cm]

[134 cm from top of ‘baseboard’ to bottom baseboard of ‘shelf 1’]

(each shelf protrudes out [2 cm])

8.5 cm from bottom shelf baseboard to top shelf baseboard

shelf 1 –>

[2 cm tall]

24.5 cm from top of shelf 1 to bottom of ‘shelf 2 baseboard’

[8.7 cm tall] from botto of shelf 2 baseboard to top of shelf 2 baseboard

[80 cm] from shelf 2 surface to closet ceiling

[130 cm] from bottom right corner to

10cm

1 meter

45cm

*LEFT WINDOW SILL* –>

XXX

*RIGHT WINDOW SILL* –>

XXX

*2.53 METERS*

*2.29 METERS*

*horizontal rectangle*

*’entrance door’ opens from the ‘south-east’*

*’closet door’ opens from the ‘south-west’*

*2 CENTI-METERS*

*9 CENTI-METERS*

*13 CENTI-METERS*

**SKETCHES**

☜*“CLIP IDEAS”* ☞
*SKETCHES*

* *TABLE OF CONTENTS* *

*we won the war*