.
-as of [8 MAY 2026]-
-TRIPODS-
(THE AMAZON LIST)
.
-[1/4”] SCREW THREAD-
(1 MALE)
1
-wireless remote shutter–
*1 CR2023 BATTERY*
(in back slot)
.
*on/off switch is on right side*
(down is off / up is on)
.
*when switched ON, a blue light will blink in ‘top left corner’ until the remote is connected to desired device*
2
-remove ‘tripod’ from ‘water-resistant carrying bag’–
3
*3 LEGS*
*4 ‘LEG LOCKS’ ON EACH LEG*
*FOLD OUT ALL 3 LEGS*
.
*minimum length* —>
[43.6 CM]
.
*maximum length* —>
[162.6 CM]
.
4
*TURN ‘CENTER COLUMN LOCKING KNOB’ LEFT TO UNLOCK*
*PULL IT UP TO DESIRED HEIGHT + THEN TURN KNOB RIGHT TO LOCK*
.
5
‘PAN LOCKING KNOB’
‘VERTICAL TILT LOCKING KNOB’
‘HANDLE’
‘DEVICE LOCKING KNOB’
‘1/4 STANDARD SCREW INTERFACE’
.
.
.
.
.
*SILVER SIZZERS*
*ALIEN TAPE ROLL*
(3 CM)
*CUT 3 SMALL STRIPS TO ATTACH TO ‘AUREDAY TRIPOD LEGS’*
.
*each leg has 4 locks*
.
[11cm ‘center pole connector bar’ from ‘ground level’ when no legs are extended)
(start unlocking/extending legs from the top down)
(because the legs get progressively ‘thinner/flimsier’)
.
*lock 1 extension* –>
[31 cm] from ‘ground level’
.
*lock 2 extension* –>
[53 cm] from ‘ground level’
.
*lock 3 extension* –>
[76.5 cm] from ‘ground level’
.
*when fully extended, the ‘aureday tripod ‘center pole connector bars are 1 meter from ‘ground level’*
.
[the 3 legs form a [80cm x 80cm x 80cm] triangle]
.
(~7.5cm extension below the ‘center pole connector’ to hold the ‘center pole extension’)
(when the ‘center pole’ is submerged, it is 33.5cm from ‘center pole connector bars’ to 1/4” clamp connector)
.
.
*’vertical tilt knob handle’ should be on same side as ‘center pole extension knob’*
.
[turn center pole knob LEFT (/ counter-clockwise) to loosen and allow for a [36.5cm] vertical extension]
[turn center pole knob RIGHT (/ clockwise) to tighten the knob back in place]
.
*turn handle LEFT to ‘vertical tilt unlock’*
*turn handle RIGHT to ‘vertical tilt lock’*
*push handle up for ‘downward tilt’*
*push handle down for ‘upward tilt’*
.
*’panning knob’ enables you to do 360º rotation shots with ‘handle’*
.
*turn ‘pan locking knob’ AWAY to ‘pan unlock’*
*turn ‘pan locking knob’ TOWARDS to ‘pan lock’
*turn handle left to rotate right*
*turn handle right to rotate left*
.
*’90º right rotation’ knob*
-above ‘handle’-
-turn left to unlock-
-turn right to lock-
.
*when unlocked, lift left side of platform and tilt right*
*turn knob right to lock*
.
(for ‘overhead shots’, the platform needs to be folded upright so that the ’30cm arm’ connects at ‘right angle’)
.
*connect the ‘long LS06 arm’ to the tripod*
*so that the ‘90º tilt’ faces right*
*knob on bottom*
*turn knob counter-clockwise to tighten*
*turn knob clockwise to loosen*
.
*turn ‘device locking knob’ counter-clockwise to tighten*
*turn ‘device locking knob’ clockwise to loosen*
.
*connect ‘short LS06 arm’ to ‘long LS06 arm’*
(the same orientation as ‘long arm’)
(twist short arm clockwise to tighten)
.
*place iphone into clamp so that there is a ‘female 1/4 screw thread’ on left side*
*under the left ‘volume down’ button*
.
*turn away to tighten*
(4-5 rotations should suffice)
*turn towards to loosen*
.
-as of [8 MAY 2026]-
.
.
*👨🔬🕵️♀️🙇♀️*SKETCHES*🙇♂️👩🔬🕵️♂️*
.
.
.
.
.
💕💝💖💓🖤💙🖤💙🖤💙🖤❤️💚💛🧡❣️💞💔💘❣️🧡💛💚❤️🖤💜🖤💙🖤💙🖤💗💖💝💘
.
.
*🌈✨ *TABLE OF CONTENTS* ✨🌷*
.
.
🔥🔥🔥🔥🔥🔥*we won the war* 🔥🔥🔥🔥🔥🔥