-as of [21 JUNE 2026]-
.
*TOOLS* —>
-[15 CM] RULER-
-YELLOW LABELS-
-[ULTRA-FINE] SHARPEE-
.
*MARK THE [4 CORNERS]* —>
.
*[30 CM] STRAIGHT SIDES* —>
*[15 CM] MIDPOINTS* —>
-LEFT SIDE-
-[PDG] LOGO-
-[6 CM] X [2 CM]-
*MARK [3 CM] HORIZONTAL MIDPOINT* —>
(THE [MIDDLE] OF THE [D])
*MEASURE THE [[73 CM] WIDTH] BY CONNECTING THE [HORIZONTAL MIDPOINTS] WITH [METER STICK]* —>
-MARK THE [[36.5 CM] MIDPOINT] WITH YELLOW [CIRCLE STICKER]* —>
*2 CABLE CLIPS* —>
-[2 CM] x [2.5 CM]-
*VERTICAL MIDPOINTS* —>
-[1.25 CM]-
(CUT OFF [EXCESS LABELING] WITH [SIZZERS]-
-THE 3 “COLUMNS” HAVE [WIDTHS] OF APPROXIMATELY [0.667 CM]-
*LINE UP THE [[CLIP] VERTICAL MIDPOINTS] WITH [[DESKTOP[ VERTICAL MIDPOINTS]* —>
-MARK THE [CLIP PERIMETERS] WITH [YELLOW LABELS]* —>
(TO EASILY REPLACE THEM)
-ATTACH A WIRE’S [LEFT ENDPOINT] TO [LEFT CLIP]-
-PULL THE WIRE TAUT THROUGH [CENTER]-
-AFFIX [WIRE] TO [RIGHT CLIP]-
*PULL THE RIGHT SIDE’S [WIRE SLACK] TO VERTICALLY ALIGN IT WITH [METER STICK]-
-ATTACH THE [WIRE] TO [METER STICK] WITH LARGE [BINDER CLIP]-
-MEASURE THE EXCESS [WIRE SLACK]-
-[73 CM] + [31 CM] = [1.04 METERS]-
-FLAT SURFACE-
-cable-
-meter stick-
-2 gold [binder clips]-
-USE EXTRA [BINDER CLIPS] TO SEAL ALONG THE WAY-
-IF THE [CABLE] IS OVER [1 METER] IN LENGTH, ADD “YELLOW LABEL” TO THE [1-METER MARK]-
-THEN MOVE THIS MARK TO THE FAR LEFT OF [METER STIX]-
-ADD THIS LENGTH TO [1 METER]-
-REPEAT IF NECESSARY-
.
.
-TOP-
.
XXX
.
.
-SECTION 1-
-SECTION 2-
-SECTION 3-
.
.
-section1start-
-SECTION 1-
X
.
-section2start-
-SECTION 2-
X
.
-section3start-
-SECTION 3-
X
.
-groundzero-
.
X
-SECTION 3-
-section3end-
.
X
-SECTION 2-
-section2end-
.
X
-SECTION 1-
-section1end-
.
.
XXX
.
-BOTTOM-
.
-SF1 TOP-
(TEMPLATE)
-SF! BOTTOM-
(TEMPLATE)
.
.
.
*👨🔬🕵️♀️🙇♀️*SKETCHES*🙇♂️👩🔬🕵️♂️*
.
.
.
*-XXX-* ☞ 👉👉👉
.
.
💕💝💖💓🖤💙🖤💙🖤💙🖤❤️💚💛🧡❣️💞💔💘❣️🧡💛💚❤️🖤💜🖤💙🖤💙🖤💗💖💝💘
.
.
*🌈✨ *TABLE OF CONTENTS* ✨🌷*
.
.
🔥🔥🔥🔥🔥🔥*we won the war* 🔥🔥🔥🔥🔥🔥
X
X